Genuine LiftMaster KPR2000 wired keypad and proximity reader — a vandal-resistant zinc keypad with a built-in 125 kHz HID proximity reader that either runs a gate on its own (2,000 users, one relay) or feeds a 26-bit Wiegand stream to a LiftMaster access controller such as the EL2000SS, EL25 or CAPXLV. Card, PIN or card-plus-PIN per user, IP68 sealed, single-gang or pedestal mount. 12–24 VDC; power supply sold separately.
Stand-alone or Wiegand? On its own the KPR2000 stores its users in the keypad and closes its relay to trigger the operator — fine for a single gate with a short user list. Wired to a controller it becomes a reader: the controller holds the database, logs events and can hold thousands of credentials. LiftMaster publishes wiring sheets for the EL2000SS and EL25; any controller with a 26-bit Wiegand input (CAPXLV, CAPXM, CAPXS, CAPAC, third-party panels) takes it the same way.
Specifications
| Part number | KPR2000 (UPC 012381109487) |
|---|---|
| Reader | 125 kHz proximity — HID 26-bit and Sentex 30-bit cards and fobs, 1–2.5 in read range |
| Keypad | 12-key backlit, 4–6 digit PINs |
| Users (stand-alone) | 2,000 — card, PIN or card + PIN |
| Outputs | Relay 1 NO / NC / C, 2 A, adjustable 1–99 s; alarm output 10 A; Wiegand 26 / 30-bit out, 8-bit ASCII burst for PIN |
| Inputs | Request-to-exit, door contact; Wiegand input for a second reader |
| Power | 12–24 VDC, about 50 mA idle / 80 mA active. LiftMaster recommends the PS12V2A 12 VDC 2 A supply (not included) |
| Networking | Links to another KPR2000, a PPWR Passport receiver or most access control systems |
| Housing | Zinc alloy, powder-coated, vandal-resistant, IP68; 5.0 × 3.2 × 1.1 in; mounts to a single-gang box or a 2.4 in square pedestal |
| Temperature | −4°F to 140°F |
| Condition | Genuine LiftMaster, new |
Works with
| Controller | Connection |
|---|---|
| LiftMaster EL2000SS and EL2000 | Wiegand — LiftMaster wiring sheet "KPR2000 to EL2000SS" |
| LiftMaster EL25 | Wiegand — LiftMaster wiring sheet "KPR2000 to EL25" |
| CAPXLV / CAPXLV2, CAPXM, CAPXS, CAPAC | Any of the four 26 / 30 / 37-bit Wiegand reader inputs |
| PPWR Passport receiver | Reader-to-receiver link |
| Any gate operator | Stand-alone: relay output to the operator's open or access input — LA400 / LA412 / LA500, CSL24U / CSW24U, DoorKing, Elite, Ramset, Viking |
Common questions
Which cards and fobs?
Standard 125 kHz HID-format 26-bit proximity cards and key fobs, and the 30-bit Sentex format LiftMaster used on its older telephone entry systems. It does not read the 13.56 MHz smart cards or the UHF windshield tags.
Can I flush-mount it?
It is a surface unit that mounts on a single-gang box or a 2.4 in pedestal face. A recessed installation needs a back box or trim you make up on site.
Does it come with a power supply?
No. Use a regulated 12 VDC supply of 2 A or more, or the 12 V accessory output on the controller if it has the capacity.
KPR2000 or a wireless keypad?
Wireless keypads (KPW5, KPW250) are quicker to fit but give you a PIN only. The KPR2000 adds cards and fobs, an event trail through the controller, and no batteries to change.
Related
EL2000SS parts · EL25 parts · CAPXL / CAPXLV parts · PPWR · KPW5 · KPW250 · Keypads, card readers and fire boxes
Tell us what controller or operator it will connect to and we will confirm the wiring — parts@gatehousesupplies.com or call 866-965-5599. We would rather confirm it than have you order twice.
